When repiping makes more sense than another repair
One leak in 20 years is a repair. Three leaks in three years is a pattern. Pinholes in copper, rust-brown water from galvanized pipe and falling pressure are signs the metal is failing from the inside, and each patch only buys time.
A repipe also suits a remodel where walls are already open, because the labor is cheaper while the studs are exposed. We tell you honestly if your pipe still has years left. For a single failure, see burst pipe repair.
PEX or copper: the plain comparison
| Question | PEX | Copper |
|---|---|---|
| Install | Flexible tubing, fewer joints, faster | Rigid, soldered or press joints. |
| Resistance to freeze splitting | Better | Splits more readily. |
| Corrosion | Does not corrode | Can pit in some water conditions. |
| Outdoor and soil use | Needs a protective sleeve in soil, per the city handout | Type L minimum for service lines. |
| UV exposure | Must be shielded from sunlight | No issue. |
Either pipe is an approved material in Milpitas when it complies with the California Plumbing Code table and the product is third-party listed and NSF/ANSI/CAN 61 certified.
How a whole-house repipe goes
Assess
We trace the existing lines, check pressure and count fixtures.
Permit and plan
The plumbing permit is requested. A building permit may also apply when walls are cut extensively.
Rough-in
New pipes go in through the attic, crawlspace and walls. A rough inspection happens before walls are closed.
Connect and test
Fixtures are reconnected and the system is pressure tested for at least 15 minutes. Final inspection follows.
Ready to plan a repipe?
Call to book a pipe assessment.
What the Milpitas Office of Building Safety expects
- A plumbing permitInstalling or replacing water piping in a building requires one. Extensive removal of walls or ceiling structure requires a building permit.
- Approved materialsPipe, fittings, solder and flux must comply with NSF/ANSI/CAN 61, and lead content is limited to 0.25 percent for pipe, fittings and fixtures and 0.2 percent for solder and flux.
- Dielectric unionsThey are required wherever dissimilar metals connect.
- Support and protectionPEX 1 inch and smaller is supported every 32 inches horizontally, copper 1 1/2 inch and smaller every 6 feet. Pipe passing within 1 inch of exposed framing needs a No. 18 gauge steel nail plate.
- Insulation and disinfectionHot water piping must be insulated, and new potable systems must be disinfected before use.
- Two inspectionsA rough inspection before wall or ceiling membranes go on and a final after work is complete.
Which Milpitas homes tend to need it
Milpitas grew fast after its 1954 incorporation, and many homes date from the 1950s and 1960s. Older homes may still have galvanized pipe, while later homes often have copper that can pinhole. We look at the pipe in the garage, at the water heater connection and under sinks to tell you which you have.
If you plan a bathroom or kitchen remodel, schedule the repipe before the drywall goes up. Combining it with a plumbing installation job saves wall repairs.
What affects repiping cost
We provide a written price before the work starts.
Insurance does not usually cover repiping for age or wear. Some policies cover damage caused by a sudden leak, so keep the repair records.
What to do first, and the code behind it
Before a repipe, locate the main shutoff and clear access to the attic or crawlspace. According to the City of Milpitas Office of Building Safety, pipe, fittings and solder must meet NSF/ANSI/CAN 61 and the material tables in the California Plumbing Code, which is based on the Uniform Plumbing Code (UPC).
Common Questions
Most take a few days, depending on the house size and wall access. We give you a schedule when we quote.
You may be without water for part of one or two days. We plan the shutoffs and tell you the windows in advance.
Yes. The city says installing or replacing water piping in a building needs a plumbing permit and typically two inspections.
Approved PEX is rated for potable water, and the city requires products to meet NSF/ANSI/CAN 61.
Yes. A partial repipe replaces the worst section, such as a failing bathroom group or the lines in one wall.
